Posted by Mike CA on August 23, 2007 at 20:44:27 from (75.31.164.246):
Today I went to a tractor junkyard in my local area. I have been there to look around, but today I knew what I needed, so I wanted to see if they could accomodate me. In the past just asking a quick question I found out that their prices were what I considered pretty high. But today I gave the parts guy my full story, and he seemed very interested in helping me out with good prices. So, below is a list of parts I found that I need, and the costs. I have some questions below that, so please read on...
- Fenders (2) + attaching hardware - $45 each. (they look orginal, one is on a '39H, and the other is on a 300, but they look the same. A camera will determine if they are original and the same... I'll post pics soon)
- Narrow front end with casts, no rims: Damage to the right seal area - $175. I think I'm going to pass on this because I think it's incredibly expensive, and it's damaged.
- Light bar w/ 2 lights (no bulbs or lens) + attaching hardware - $45
- Oil pan in decent shape $45
- Throttle linkage arm + hardware - $15
- Hydraulic control arm and link rod $40
- Seat tube assembly (with spring and base) $20
- Amp control box $20
- Lower radiator pipe - $5
- Carb breather tube - $10
- H4 mag core (to give to Magman) $50
FREE WITH OTHER PURCHASE:
- Hydraulic line plugs
- Block water drain plug
- Rusted battery box support
- Wing nut carb adjuster
Questions:
- Are the lights repairable? One has a small dent in it. Is that repairable? Would it be smarter (cheaper) to buy these original lights and rebuild/restore them, or buy aftermarkets OEM lights?
- Can the throttle linkage arm be straigtened easily? How do you do that? I was going to buy a new one because mine is bent. But it's been welded, and the new one is pretty cheap.
- On the battery box support, it has scaled rust. Can that be restored to usable condition? I haven't seen them in a catalog, can they be purchased new?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Hydraulics - The Basics - by Curtis Von Fange. Hydraulics was one of the greatest inventions for helping man compound the work he can do. It’s amazing how a little floor jack can lift tons and tons of weight with just the flick of a handle. What’s even more amazing is that all the principals of hydraulic theory can be wrapped up in such a small package. This same package applies to any hydraulic system from the largest bulldozer to the oldest and smallest tractor. This short series will take a look at the basic layout of a simple hydraul
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.