Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: howe do you remove hydraulic line shaft from hub?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by CarolynDiesel8N on September 01, 2012 at 15:05:27 from (70.192.66.1):

In Reply to: Re: how do you remove hydraulic line shaft from hub? posted by Pitch on September 01, 2012 at 04:31:56:

Greetings,
Thank you for such a fast response. The pump is in the front of the tractor and the shaft comes through a small hole in the front of the tractor to couple to the pump. The back end of the shaft goes into a hydraulic hub attached to the front of the engine. It is separate from the three point hitch in back. That one works just fine.
When I run the engine, the shaft runs at a significantly lower speed than the engine. When I uncouple the shaft from the pump, it turns at the same speed as the engine. The current speed which the shaft turns is too slow to power the pump, it turns slowly, then speed up a turn, then slow again.
Since the shaft is running through the front of the tractor, I can not really get a good view to see what is going on. I can tell that the shaft does spin freely inside the hub. I know someone mentioned cutting the shaft, but the space is so tight.
It is my understanding that I need to pull the shaft out the front of the tractor, which once it is out, will allow me to remove the hub from the engine area. This is where I am stuck.
I will try "Old"'s recommendation to grab and try to pull out, but I have been trying that without any luck. Very tight space and limited angles. Any other suggestions on how to accomplish this - the tricks would be appreciated. I have the coupler flange on the end that connects to the pump. I removed the screw that holds it on, but it would not budge. Do you get that off by tapping it on all sides?
I understand what I need to do...I just need to know how to get it done.
Thank you,
Carolyn Diesel 8N


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy