Posted by John Deere D on August 10, 2019 at 23:01:33 from (204.244.59.66):
In Reply to: Loose Flywheel on 730 posted by Joel Sanderson on August 10, 2019 at 21:01:07:
Someone shall come and explain what and how you adjust and tighten your flywheel:
This Flywheel BORE has been bored tapered.
Then a matching Tapered sleeve has been inserted into the Flywheel:
Once you position the FLYWHEEL on the crankshaft...you tighten the SQUARE NUT ….this in turn draws the taper lock into the taper bore of the flywheel that in turns caused the splines of the taper lock to become tight on the crankshaft.
Once the flywheel is tight on the Crankshaft, with a dial indictor, I would check the amount of running THRUST clearance the crankshaft has.....
You have an original flywheel with the Nuts welded to the original Through Bolts ...I WOULD NOT LOOSEN the NUTS from the BOLTS:
Some one shall explain the proper tightening procedure…..
You may be more enlightened if this topic was posted in the John Deere Section?
The repair on your Fathers Tractor is a very good upgrade....you need to know the installation procedure...….I have no hands on with the installation of this type of device on a Farm Tractor.
If this was my tractor I would ask myself.....WHY is this FLYWHEEL LOOSE ?...….What has failed to cause this Flywheel to become loose?
Cracked Flywheel..?????....Through Bolts of Flywheel have failed...??..etc..etc..
Flywheel was not installed as per tried ,tested procedure..??
What all should I check before I set the Flywheel and tighten the Taper lock...?
Once this Flywheel is in place and the taper lock is tightened it is NOT EASY to loosen off the Flywheel:
It's imperative to have the proper installation procedure and to follow the procedure:
I have never installed a taper lock on a Tractor Flywheel.....I have installed dozens of taper locks in the petrol Chemical Industry:
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Gatherin of the Orange - by Rick Nikolich. In July of 1998 I was talking to fellow Allis Chalmers collector Mike Schilling about the annual "Gathering of The Orange" AC show coming up in August of 1999. He got this wild idea that we should get a convoy of AC tractors and drive them from Charlotte, Michigan 105 miles to LaGrange, Indiana.
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
