Posted by the tractor vet on December 08, 2022 at 22:05:30 from (108.220.145.239):
In Reply to: Re: ih pressure plate posted by J Hamilton on December 08, 2022 at 19:44:18:
Ya can put a pressure plate from a 706-806 in a S/MTA BUT you best have some leg mussel . It all has to do with what springs are used for the disc once again is it fiber or how many pads . Spline and shaft size is the big thing . To stop the slipping on one of my customers S/M T A after the rebuild and up grade the stock clutch would not hold and e3ven upping to the 560 plate it slipped under load . We then went with a stock 706-806 and put the power to the wheels . His M T A on the dyno has just under a stock 806 D and yes he does farm with it and has been in the same family since new . Even burnt under a two row mounted corn picker and rebuilt and when we did the rebuild back in like 95 the last time was after it burnt in 56 when it got the upgrades . I spent a lot of time finding the stuff used the first time to do it like it was done before . I own a S/MTA with all the upgrades from M & W and mine will put out 60 Hp. Vernon's will do 94 and change . i can pull 3x16's in third at 8-9 inches deep in our ground Vernon can pull four 16's in third and flat up and run away from me . He can put it on the New Holland grinder mixer and grind corn out of the crib almost as well as my 806 D Yea it took a good pressure plate to put the power to the ground BUT man that pedal is stiff and ya don't set long holding it down .
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.