Tractor Talk Discussion Board |
Re: Re: How are piston rings made?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Glenn in MI on January 31, 2004 at 07:11:36 from (65.148.91.177):
In Reply to: Re: How are piston rings made? posted by Vern-MI on January 30, 2004 at 15:46:04:
Your tale brought back many memories of working at Sealed Power in St Johns, 1969-71. Our headquarters and one plant was in Muskegon - not sure if the company was originally known as Muskegon Piston Ring or not. After going through the Cam Turn and Inside Bore, the next stop was my station - the Finish Mill which had a traveling table with an arbor of rings which run under a spindle carrying a small saw blade which trimmed the slot. It looked much like a radial arm saw with a tiny blade. The slot width was controlled to about 2 or 3 thousandths of an inch with shims behind the precision jig that held the rings. Production averaged about 48,000 rings a night on my station. I still remember how sharp the rings were - always had some cuts. The next stop for the rings was the most boring operation in the factory - the Pip Marker. That put a dot on one side of each ring so you could tell which side was up. Apparently that was important for the final operations and for installing the rings. I forget what we called the final operation that machined the rings to ten-thousandths of in inch precision, but the machines generated a lot of heat - not a good job for the middle of the summer. There was also a chrome plating operation for some rings, a heat treating oven that I occasionally ran, degreasing tanks, and other operations. It was a mind-numbing job - enough to convince me to go off to college, and a career in computer technical support. I had a chance to visit Oldsmobile's engine plant near Lansing in 1985, and what a difference! Most machines were computer controlled, automatic conveyors moved all parts, and it was operated by a fraction of the workers that would have been required in earlier years. The St Johns factory is still open, but is owned by Dana, now. I'm not sure how much longer it will be there, I've heard rumors that another outfit is trying to buy Dana. I think the Muskegon plant is closed.
Follow Ups:
Home
| Forums
Today's Featured Article -
Gatherin of the Orange - by Rick Nikolich. In July of 1998 I was talking to fellow Allis Chalmers collector Mike Schilling about the annual "Gathering of The Orange" AC show coming up in August of 1999. He got this wild idea that we should get a convoy of AC tractors and drive them from Charlotte, Michigan 105 miles to LaGrange, Indiana.
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|