Posted by Jerry/MT on April 23, 2010 at 12:43:36 from (206.183.116.129):
In Reply to: 2-4-D Amine posted by mss3020 on April 23, 2010 at 06:08:24:
I applaud you or being a responsible person for wanting to take care of your pasture weeds. I wish my neighbors would do that, too.
However, as a rancher who uses herbicides, it always scares me when I hear these types of questions , especially when you say".. I use 12 cups per 50 gallons but "...my buddy is using 16 cups for 50 gallons..." 12 cups per 50 gallons that 6 pints per 50 gallons. Now if you put that uniformally on 35 acres, that"s 6/35 pts per acre or O.17 pts per acre. Respectfully, that"s a good way to start breeding resistant weeds! And that"s the last thing we need. It"s hard to get new herbicides approved by the EPA and we don"t need to have the ones we have become ineffective.
You are required to use herbicide per the label instructions usually expressed in pints of herbicide per acre. To do that you need to know the the total flow rate from the nozzles(~gpm)at the particular pressure you are spraying at, the coverage of the spray boom(w~ft) and the speed of your spray rig(~mph). So if you use 1 pt in 10 gallons and want to put on 1 pt of herbicide per acre(10 gallons of mix with at 1 pt herbicide)and your spray is w ft wide
10 gallons per acre= (gpm x 5940)/(mph x w). You can go to your county extension office and they can give you some literature about how to figure this out, and how to calibrate your nozzles, and how to figure out your speed. It"s not rocket science and it"s relatively easy to do. So do yourself and the rest of the agriculture community a favor and if you are going to spray for weeds, do it right.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.