Posted by BushogPapa on January 08, 2017 at 12:59:17 from (107.10.186.248):
In Reply to: Re: Back surgery posted by bass on January 08, 2017 at 10:06:42:
Similar situation here...Discectomy, L5-S1 Fusion but still had the PAIN in my Hip, numbness in my thigh and my foot would also go numb....
Neurosurgeon wanted to do a 2nd Fusion..( "We can just move those Rods UP"..) she said..
NOW..HERE is what I did and I HOPE you take my advice about this....
I found a physician who Specializes in PAIN Management..treats really SEVERE Pain ( The Worst kinds )..
He CAN relieve Pain and I have confidence mine could pretty much eliminate your pain..
I have a Neuro-Stimulator in my side that powers a set ( 2) of leads up beside my Spinal Chord that create a magnetic field across my Spinal Chord and that has Completely eliminated my numbness and at least 90% of any pain..!!
Hey, if need be, he can even put in a Morphine pump..but you wont need anything like that ( usually reserved for Cancer victims, etc).
A Neuro-Surgeon will NOT tell you abouot this option and I LIKE My Dr's Motto.." You have many Options before you have to Submit to a Knife"..!!
Mine was put in in 2011 and now I can leave mine set so LOW I have NO idea it is even ON..and if I turn it off ( for an EKG. etc, my pain may not come back for a WEEK or more if I forget to turn it back on ( I use a small strong Magnet).
Here, my Dr's name is Gladstone Churchill McDowell and he can be contacted at 614-383-6450
I am sure their Office will try to refer you..they DO Screen New Patients closely, so don't be surprised if they send you to a second Dr for evaluation at the beginning.. Hope you DO look into this..I have gone from using a CANE ( with a Seat on it) to actively Western Square Dancing and Round Dancing..!!!
I am in Ohio and Dr. McDowell is in Columbus, Ohio.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.