Posted by cjunrau on July 15, 2018 at 07:09:58 from (204.112.13.183):
was a post the other day asking fuel cost of making hay. I cut 5 acres an hour with a 4230 JD tractor. Field is so ruff that I can only go 4.5-5.5 MPH I use 25 litres of fuel an hour =$31.50 an hour. Divided by 5 is $6.30 an acres. One field I got 3/4 of a bale = $8.40 a bale. Baling and raking is about the same as cutting. so double that and you get $16.80 a bale to make hay on that field. I pay $20 a bale rent. That leaves very little profit for my time. That was this year at 21 bales. Last year with the same cost, same field I got 50 bales. So that cut the cost per bale in half or a little better. So if you have a smooth field where you can go 10 MPH baling uses a lot less fuel per field even though by the hour it still costs the same. So there is no cut and dry cost per bale. My fresh field this year I silage wrapped 30 5X5 bales off of 6.5 acres. About 2.5-3 bales an acre if it was dry hay. Smooth field but could only cut in places in A2 Quad range because it was 5 ft high. Mostly wild mustered and oats. where it was not as tall could go faster. Baling with a 2394 Case IH tractor this year and fuel cost is half of what the 4230 JD uses baling. I like having 2 tractors now as I don't halve to unhook and rehook all the time. Cut another 25 acres of barley , under seeded in alfalfa yesterday. Looks like that field will be 2.5 bales an acre and should be able to bale dry tomorrow. We have 25degrees + Celsius. and 20-30 MPH wind so it is drying fast.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.