TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Farmall & IHC Tractors Discussion Forum

100/a and farmall 200/sc interchange

Welcome Guest, Log in or Register

Author

wegman in Mn

10-20-2006 07:45:09

Report to Moderator

can the bell housing on the 200/sc interchange with the one on the 100/a and will the 100/a front axle assembly bolt onto the 200/sc front

[Log in to Reply] [No Email]

james Coombs

10-22-2006 20:01:14

Report to Moderator

Re: 100/a and farmall 200/sc interchange in reply to wegman in Mn, 10-20-2006 07:45:09

let me correct my self the tork tube just might fit but the front end will not fit .also the govenor will not be set right the 200 runs about 1875 the 100runs 1540rpm .top no load speed.

[Log in to Reply] [No Email]

james Coombs

10-22-2006 19:34:22

Report to Moderator

Re: 100/a and farmall 200/sc interchange in reply to wegman in Mn, 10-20-2006 07:45:09

the motor block is the same on the A and C I thenk every thing else is diffrent. probbly the same on the 100 and the 200.

[Log in to Reply] [No Email]

Hugh MacKay

10-21-2006 02:44:27

Report to Moderator

Re: 100/a and farmall 200/sc interchange in reply to wegman in Mn, 10-20-2006 07:45:09

The torque tube will be the same at the clutch end, but I'm not sure it will match up at transmission. Your best bet is check out part numbers

The front end is another matter, you definitely can not switch front casting as the steering shaft on offsets goes along right side of engine, whereas SC, 200, etc. the steering shaft goes along left side. Even if you could change the steering shaft to other side, the offset axle on a SC would be offset.

Now, you may be able to change the front axle at pivot point, however the SC, 200, etc will use a much larger pin, plus SC, 200, etc. front axle has a stabilizer. SC, 200 axle assembly is somewhat heavier than offset, your courting disaster on this one.

To sumerize, torque tube, cross reference part numbers, I think it may work. On the front axle forget it, you'll buy SC, 200, etc. parts for less money than your modifications are going to cost.

[Log in to Reply] [No Email]

tractorsam

10-20-2006 17:37:44

Report to Moderator

Re: 100/a and farmall 200/sc interchange in reply to wegman in Mn, 10-20-2006 07:45:09

First off, I think the front axle (along with its mounting casting) would bolt up but it wouldn't work anything like it should. There are some pretty major steering issues and the pivot point wouldn't be in the center of the tractor. As to the bell housing, ignoring the A and the B I think they are more or less the same. However I can't remember about the support near the steering universal joint. If it's supported on the torque tube there could be a difference, if not I'd think it should work. I don't know that this helps, tractorsam

[Log in to Reply] [No Email]

teddy52food

10-20-2006 10:26:37

Report to Moderator

Re: 100/a and farmall 200/sc interchange in reply to wegman in Mn, 10-20-2006 07:45:09

They may bolt up,but the steering is on opposite sides. I'm not sure about the bell housing. Someone else will know .

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy