Posted by George Marsh on August 07, 2012 at 13:02:37 from (50.104.225.241):
There has been a lot said about power factoring motors, so I had some time to play in my cool basement. My well has a 3/4 hp A O Smith pump. It operates on 120v. I put a 12 gauge cord on it by buying a 6 ft extension cord and cutting 3 ft off the end. Took the other end of the cord and put a plug on it. Removed some of the insulation so I could put ammprobe around the power wire. Plugged my pump in the end of my 3 ft extension cord.
To my surprise, when the pump kicks on around 20 psi, my amp draw is close to 15 amps. As the pressure builds, the amp draw decreases to 12.2 amps. The more the pressure, the less the amps. That seems odd to me, I would have thought just the opposite.
I have 2 55 mic 440 Volt capacitors. By connecting a capacitor to the end of the white cord, I could plug the capacitor into my 3 ft extension cord and also have the well pump plugged into the same cord. This puts the 55 mic in parallel with the pump and the total current decreased by 1.1 amps. Putting the second 55 mic cap in parallel with the first, my total current went from 12.2 amps to 9.99 amps. I was impressed with my results. Even had a little excitement too, especially after unplugging the capacitors and shorting them. I confirmed the big ban theory.
Going to get a metal box, some bleeder resistors, fine tune the bank of capacitors for minimum current and install them on the side of the switch where the pump is connected.
Next I tried to power factor a 4 peak hp electric chain saw. My results were the opposite of my well. Adding any size capacitor caused my total current to increase. I started with a 4 mic and stopped with a 55 mic.
So, are you not able to power a universal motor?
Are you not able to power factor a universal motor that's not under load?
I'm sure there are some will say that I don't have a clue what I'm doing, so I'll put that out there as one of the options.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.