|
Tune-Up Specifications - John Deere |
This data has been gathered from old out-of-print material. While
we make every effort to be accurate, the information shown is to
be used for general reference only. It is always best to have
the original service or operator's manual for your tractor before
attempting any tuneup.
There is a legend at the bottom of the page describing some of the terms used here.
|
Model
|
Point Gap
|
Spark Plug Gap
|
Timing Mark On
|
Spark Occurs
|
Firing Order
|
Int. Valve Clearance
|
Exh. Valve Clearance
|
Comments
|
|
M,MT |
.020 |
.025 |
FLY |
TDC |
1-2 |
.012C |
.012C |
For magneto set point gap to .015 |
|
L,LA |
.020 |
.025 |
FLY |
TDC |
1-2 |
.006H |
.008H |
For magneto set point gap to .015 |
|
H (All Fuel) |
.015 |
.030 |
FLY |
|
1-2 |
.015H |
.015H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
G (All Fuel) |
.021 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
For magneto set point gap to .015 - Spark occurs when dot or "LH-Impulse" aligns with index on cover or case. |
|
D (All Fuel) |
.015 |
.030 |
FLY |
|
1-2 |
.030H |
.030H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
B (All Fuel & Gas) |
.015 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
A (All Fuel & Gas) |
.021 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
For magneto set point gap to .015 - Spark occurs when dot or "LH-Impulse" aligns with index on cover or case. |
|
80 Cranking Engine |
.020 |
.025 |
FLY |
30 deg. BTDC |
1-2-3-4 |
|
|
|
|
70 Cranking Engine |
.020 |
.025 |
FLY |
30 deg. BTDC |
1-2-3-4 |
.020H |
.020H |
|
|
70 (LP), 60 (LP) |
.022 |
.030 |
FLY |
5 deg ATDC |
1-2 |
.020H |
.020H |
|
|
70 (Gas) |
.022 |
.030 |
FLY |
10 deg. ATDC |
1-2 |
.020H |
.020H |
|
|
70 (All Fuel), 60 (All Fuel) |
.022 |
.030 |
FLY |
TDC |
1-2 |
.020H |
.020H |
|
|
50 & 60 (LP & Gas) |
.022 |
.030 |
FLY |
5 deg ATDC |
1-2 |
.020H |
.020H |
|
|
50 (All Fuel) |
.022 |
.030 |
FLY |
TDC |
1-2 |
.020H |
.020H |
For point gap, for LP set TDC. |
|
40 (All Fuel) |
.022 |
.025 |
FLY |
3 deg ATDC |
1-2 |
.012C |
.012C |
For point gap, for LP set TDC. |
| Legend |
|---|
- TDC - Top Dead Center
- FP - Crankshaft Fan Drive Pulley
- Exh - Exhaust
- Int - Intake
- ATDC - After Top Dead Center
- BTDC - Before Top Dead Center
|
|
Data collected from an old Niehoff tune-up chart.
|
Home
| Forums
| Order Support
Today's Featured Article -
Welding Basics - by Curtis Von Fange. One of the most useful skills that an owner of older equipment can have is the knowledge and ability to weld. It seems like the older equipment can do a job, albeit slowly compared to newer stuff, but it tends to break more often. Many of the breakdowns are related to the implements that are being used: the disc, wagon or bushog are among them. Knowing how to fix stress cracks, reinforce weak joints by welding on steel support plates, or cutting and shaping parts and adapters out of raw stee
... [Read Article]
Latest Ad:
2018 Kubota L2501 HST with L525 Loader. Comes with 1250 Landpride Rotortiller, 60 Landpride Box Blade, Landpride 60 Bush Hog, Landpride tandem Disc, . Has a quick detach complex, and the tires are over 50. Hrs. at the present time are 398, however just replaced the tach cable so the hrs are not accu
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
