Farmall & IHC Tractors Discussion Board |
Re: H log skidder
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Bob Kerr on July 26, 2007 at 21:40:17 from (64.12.117.137):
In Reply to: Re: H log skidder posted by georgeky on July 26, 2007 at 20:39:53:
Hi George, Yep, it is more how you do it that what you do it with. I have a little 024 shihl I cut everything with. If it is bigger than what I can do with the saw, I use a good ol fashioned crosscut. That cross cut has saved me a ton of money since it is rare I have to use it and you know what the big saws cost. This tree I just flat read wrong. It had a slight "S" bend to it and not much of a top.I thought it would go one way and it decided to go the opposite when it finally did go. I looked at the stump and there was only a half inch of vertical wood that was undercut, holding the tree up. It basicly just balanced on the stump and it is a 60 ft tree with no top mind you. I have to tell you the waiting on it to fall is worse than picking up a first date. There was no wind at all that day. That H really impressed me and I am almost thinking it might be a stronger engine than the M or at least close. I need to pull those plugs and check the pistons, I bet it has some "good ones" in there. It did use some oil though. I did some fiddling with the carb as I pulled logs up hill and I got it leaned out where it doesn't have black smoke under load and it wants a little choke when starting and it really runs nice when it warms up but after running hard it wanted to run on a bit when shutting it off. Maybe it just needs to get good and cleaned out. As far as the M goes, well the power steering started leaking like crazy one day and the next it just dripped a little. Also the 3 point lift wasn't working so good and it is driven off the PS pump. On top of that, the clicking noise is back in the clutch with a load on it.I have some figuring to do on it I think, but I need to get those logs loaded before they spoil.
Replies:
Home
| Forums
Today's Featured Article -
History of the Nuffield Tractor: Conclusion - by Anthony West. In the last piece I mentioned that Nuffield had reached the stage where they had chosen to drop the "Universal" from production. The two new models were given three figure numbers, instead of "three" and "four". Model numbers were introduced to help farmers and dealers instantly recognize the engine size and horsepower of the tractor, the 4/60 had a four cylinder diesel engine which developed 60 bhp at 2,000 rpm. The 3/42 had a 3 cylinder diesel engine which produced 42 bhp at 2,000 rpm. Th
... [Read Article]
Latest Ad:
1953 Ford Jubilee Tractor. Last driven 5 yrs ago. Parked ever since. As is as seen
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|