I've had customers run into that situation a time or two and asked me to make a jumper for them. The only time I had a problem I absolutely couldn't get past, at least not economically, and still have a factory looking setup (what he wanted) was when one wanted me to make a Bobcat attachment work on a Komatsu. If the Komatsu had had enough function buttons I could have made it work. Unfortunately the Bobcat needed like 4 functions and the Komatsu had only wiring/room for 2, or something like that. Too, the way the Komatsu was done there was no way to add any additional functions without a lot of time and expense, due to the whole 'computer' mess that the newer machines have.
I have yet to see a computer on any of the attachments. Yes, the 'newer' machines have a computer that recieves low amperage signals from the function switches. Then, all the computer does is energize the correct solenoid valve to energize the aux flow itself, or use the low voltage signal to open/close a relay to stop/send a full voltage, high amp signal to the correct function on the attachment.
Now the simplest of the Bobcat attachments I have seen have the functions operated directly by the aux flow controller (ie a rotary broom running either fwd or rev). Now for attachments like a 4or6 way dozer blade, you turn on the aux flow and it runs through a solenoid valve block with enough valves to handle the separate functions. That being the case there is typically a pin, in the connector, to energize the solenoid for each functional direction (ie- pin 1 for up, pin 2 for down, pin 3 for left, pin 4 for right, and so forth).
That all said, depending on what attachment your looking at it may or may not work. The deal breaker is if the attachment needs more functions to operate than your machine can send signals to. For instance a dozer blade needing to operate 3 cylinders would need a minimum of a 6 pin connector to handle the functions. Even then you'd more than likely see a 7 pin connector (what some older Bobcats had even though they usually didn't use all 7 places) to allow the operation of the solenoid valves on the attachment plus a dedicated ground to insure the attachment had a sure ground, and not just one through the attachment plate.
Ultimately what your going to have to do is see what the 4 pins on your machine do. It may be set up for a single function (2 pins), a ground (the third pin), and an extra/unused one (the 4th pin). Then see how many functions you need to operate the attachment and compare the two. IF there are enough functions/pins then you can usually get a diagram of the wiring system from Bobcat to see how their connector is set up, and then one for your machine to see how it's set up. From there get the mates for each connector and make yourself an adapter with the proper pins in the proper spots in each of the connectors.
Like I said, I have done this several times over the years, and except for the aforementioned situations that would keep you from making a direct connection, I haven't had any problems thus far. With that said, there are ways to make anything work given enough time, money for the various parts and pieces, and a little ingenuity....but that's a whole 'nother story....
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
