Posted by JD Seller on May 08, 2016 at 08:43:29 from (208.126.198.123):
In Reply to: o/t at the sale posted by larry@stinescorner on May 08, 2016 at 04:58:57:
Larry Two points of views on this post.
1) The girl used a calculator for a simple math problem. Well many schools are letting/making the kids use calculators at young ages so very little "math" basics are learned anymore. My youngest grand kids are NOT taught division at school. They are give a calculator to divide anything. Long division with the decimal point has not been taught for over ten years. So the young girl is part of a generation that has been schooled to use machines for a very simple task from a young age.
2) The young girl is working, which is getting rare. She got your you order correctly and in a timely manner. She even double checked the order that she wrote down. I would hire her in a minute. Many are too smart to work and defiantly not going to check their work to make it right.
P.S. My Father was a walking calculator. He could do multiplication of up to five digit number faster than you could run them through a calculator. He did spend some time with my sons. About two years ago they where working on a welding project in the shop and they needed to figure the hypotenuse of a triangle to make a truss/brace. My Father was there and rattled off his answer. They used that and built the rest of the truss. Later when we went to install i9t we found out he was "off" by more than an inch. It took us another two hours to rebuild the truss. I told them to not trust their own mental math and NEVER trust my Father's anymore, on things that had to be exact. They make fun of me using my flip phone as a calculator all of the time. I do estimates in my head but double check them with a calculator. I can do all the require math with pen and paper but usually do not have them handy.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Measuring with Calipers - by Staff. The legs of inside calipers are curved outward at the extremities to facilitate measuring small holes, while outside caliper legs have a large curve inward to increase their capacity for large work. Firm-joint calipers are adjusted approximately by the hands and then set to the feel of the work by tapping them on a metal surface. It is a common practice when opening calipers by this means to tap the top of the joint. It is better, if possible, to tap the inside of the legs, as repeated blo
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.