THe vacuum for the secondary diaphragm comes through passages that are ported from the venturies. I blew those passages out with carb cleaner when I had the diaphragm housing off the carb. Again, the secondaries move freely by hand when I have the throttle open so I don't think its a clearance issue. I am sure the secondaries aren't opening at any point when the engine is running. The carb has an electric governor. THe previous owner had disconnected the wiring from the governor and actually removed it so I wouldn't even know where to wire it up. I read that the only thing the governor would do is actully close the secondaries to limit rpms. I don't think it would have anything to so with actually opening them. Just in case I left the arm of the mechanical part of the governor disconnected from the piece that would control the secondaries so it cannot physically interfere with the secondaries now no matter what. The only part I forgot to check is the there could be a bad seal between the vacuum diphragm housing and the carb itself. To check that I need to get some rubber hose on the tips of a needle nose piers, press the hoses with the pliers over the vacuum passages inside the venturies, then press up on the vacuum diaphragm rod and see if it leaks between the diaphragm housing and the carb.
As to the edelbrock carbs, the performer is actually a Carter AFB. I just happen to look on CL a bit ago and see a guy who has two edelbrock performer 1407's. THose are manual choke and vacuum secondaries and 750 cfm's. Probably work fine on this application. Anyways one is still NIB and the other came off his 54 ford. He said it looks new and was working fine but his son swapped it for a fuel injection kit. I'm snagging the pair for $300. That's less than the price of one new so score for me.I'll still check to see if that little gasket is bad. If I can't get it working on the Holley I'll swap on the Edelbrock. If I don't end up using the Edelbrock that's okay because its a good deal and I'm sure I can get into something that I can use it on soon.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
