Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Learning to drive a Massey Ferguson 65 Tractor


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Janicholson on September 26, 2017 at 18:27:10 from (63.152.227.166):

In Reply to: Learning to drive a Massey Ferguson 65 Tractor posted by Aussie Perry on September 26, 2017 at 17:16:07:

Running a "slasher" (I assume it is a rotary brush cutter often called "Bush Hog " though that is a Common Brand).
First, They need to be operated at or very near full engine speed. The blades need to have a specific speed to function and
lift the material being shredded. This means the ground speed is regulated by gear selection, not throttle. Start in low gear
(slow) and move faster by changing to higher speed gears as confidence and results are gained. Too fast and the engine will
labor or results will be ragged.
Second, adjust the angle of the slasher so the rear of the swing of the blades (furthest rearward travel of the arc of the tip of
the blade) is 12 to 14mm higher than the front of the blade travel. Measured on flat paved surface, with the whole machine on
the same surface. This prevents the blade from continuing to cut the same stubble more than once.
Third, be willing to cut 1/2 width passes in heavy material. This can assist in a clean job in heavy growth.
Fourth, Sharpen the blades to a 1mm edge, not knife sharp. they will cut well and not dull as rapidly.
Fifth, Check the gear oil level in the drive gears every time you use it until you are sure it is not leaking, then every 10 days
of use or so. Use the correct oil.
Sixth, grease the fittings for the universal joints every time it is used for more than an hour.
Seventh, Walk the fields or areas you will mow to assure there are no pipes, fence posts, rocks, or stumps sticking up to wreck
the slasher.
Eighth, Never allow anyone to be near it on the ground when operating, it throws things, and is very nasty
Ninth, If it is mounted on the hitch, do not run it when lifted more than 20cm above normal height to avoid damaging the Ujoints
in the drive line.
Tenth, Do not get off of the tractor until it has stopped turning.
Eleventh, There is either a slip clutch or a shear bolt in the drive. Do not use stronger bolts for shear, or tighten the slip
clutch. It will break the gears or shafts.
Twelfth, Do not drive sideways on hills of more than 15 degrees of slope (conservative, but tipover is not good)
Thirteenth, Listen to the machine and carefully notice changes in sound. Things do get wound up on the shaft and can make heat.
Balance problems from material stuck on the blades can cause vibration. Stop if change is noticed.
Fourteenth, Look behind to assure it is doing its job.
Fifteenth, If it is a pull behind type hooked to the draw bar with a pin, do not turn sharp when it is running. Maybe a 12m
radius arc, not a tight turn. The Ujoints can not be angled radically. If knocking noise is heard, straighten out.
The above is coupled with experiance and prudence to make a good clean safe job well done. Jim


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership, ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy