Tractor Talk Discussion Board |
Re: maintaining batteries
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Don Denhardt on December 09, 2001 at 14:18:45 from (24.13.42.170):
In Reply to: maintaining batteries posted by Don E. Foster on December 09, 2001 at 10:34:07:
Take heart there is a cure. As a matter of fact, after you read the following you can get all the free batteries you wish. When batteries discharge some of the acid in the electrolyte converts to lead sulfate crystals that will start to coat the plates. These sulfate crystals interfere with and reduce battery capacity. If the battery is in use daily MOST (but not all) of the sulfates are reconverted back into acid when the battery is charged. This is why a discharged battery will read a low Specific Gravity (acid content lost) Batteries in storage must be kept on a trickle charger or the self discharging properties of a battery will sulfate it rapidly. Some of the sulfates will form stubborn patches that will grow in time. This growth will continue until all the plate area is covered or when the growth is big enough in one area to physically crack the plate and make it short. That is why your car battery, for example, only lasts a few years. There are only two cures for a sulfated battery. 1. EDTA treatment (messy, hazardous and will foul up the electrolyte) 2. Desulfation by electronic pulse The link below has instructions for a homemade electronic pulse desulfator. If you do not know how to solder or do not have a grounded tip soldering iron, assembled kits are available.
http://shaka.com/~kalepa/desulf.htm After you build or buy a pulser, you can grab the batteries everyone else is throwing out and recover them. Simply go to any recycle center or battery retailer and get the discarded batteries that still measure 10.5V (12V battery) or 5.25V (6V battery). Bring them home and put them on a trickle charger and pulser and usually within a few weeks to a month, they are like new again. Good Luck, Don
Follow Ups:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|