Posted by Adirondack case guy on August 24, 2020 at 17:21:10 from (74.76.16.33):
The heat has dissipated a bit after a really hot July. All the 1st. and 2nd. cut hay has been harvested, and oats and straw are all harvested and baled and I have my helper back for this week, before 3rd cut hay beggins, and beans are ready. We have been getting lots of afternoon T storms so it has been a bit slow going. Storm yesterday was pretty strong. Some really strong winds that took down some trees and knocked down some of the beans. My cousin and Dustin managed to finish baling the oat straw and got the wagons under cover before the storm hit. I recorded 2.34" of rain in the time it took to pass plus some hail Dustin and I made a load last week in smaller trailer (about 1-1/4 cord), and today we filled the big trailer with a bit over 1-1/2 cord. It is supposed to rain again tomorrow and Wed. so we will unload and stack what we processed today in the woodshed tomorrow, weather permitting.----I do all my skidding in the woods with my Kubota B2150 equipped with loader and shop built 3pt skidding arch. It gets in between the trees well and leaves very little collateral damage. Things go pretty quickly when the logs are blocked and Dustin just has to set them on or roll the heavy blocks to lifting tray on my shop built splitter and elevator.
I have built swing out tool racks onto the sides of my processor tractor to carry everything we need when processing wood, including places to hold saws, and splitter fuel and food and drink for ourselves.
Todays load with the bigger trailer and my 831C.
The lifting tray can be mounted on either side of the splitter and folds up over the splitter for transport. I recently built a stabilizer leg assy. that I can adjust to support the splitter rather than just suspending it on the 3pt of the tractor and that also folds up by removing one pin and folding the legs up and putting the pin back into a transport position.You may have also noticed the comfy seat in the earlier pics. I don't always have Dustin's help, so when he is not here my wife comes up and runs the splitter and elevator for me while I gather up and split the blocks. Elevator is powered by the splitter only when the cylinder returns to retracted position. Just a single spool valve and elevator does not have to run constantly. The elevator gets hooked to a hitch on the back of splitter for transport.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
Nice Marvel Schebler DLTX 8 bronze body carburetor For 1934-1936 unstyled A tractor.Serial No.410000-42850. All restored and ready to use.
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
I have built swing out tool racks onto the sides of my processor tractor to carry everything we need when processing wood, including places to hold saws, and splitter fuel and food and drink for ourselves.
Todays load with the bigger trailer and my 831C.
The lifting tray can be mounted on either side of the splitter and folds up over the splitter for transport. I recently built a stabilizer leg assy. that I can adjust to support the splitter rather than just suspending it on the 3pt of the tractor and that also folds up by removing one pin and folding the legs up and putting the pin back into a transport position.You may have also noticed the comfy seat in the earlier pics. I don't always have Dustin's help, so when he is not here my wife comes up and runs the splitter and elevator for me while I gather up and split the blocks. Elevator is powered by the splitter only when the cylinder returns to retracted position. Just a single spool valve and elevator does not have to run constantly. The elevator gets hooked to a hitch on the back of splitter for transport.
Loren