Posted by Steve@Advance on March 14, 2021 at 08:22:51 from (66.169.147.211):
In Reply to: Massey Ferguson 202 posted by youngfrmr on March 13, 2021 at 19:50:34:
That tractor closely resembles the MF35 farm tractor, but with a heavier front end for loader work.
As far as I know the transmission and gear cases are the same and probably came with GL1 90w mineral oil. GL1 does not contain EP additives, which is what the brass pump components require.
Being a single grade oil, (that is all that was available then) it gets really stiff in cold weather, which will slow down the hydraulics until it gets up to temperature. The common substitute is 15w-40 diesel engine oil. Cheap and available anywhere!
Those transmissions are incredibly tough! Not picky about lubrication, as you probably found water inside, so many run unknowingly with more water than oil!
How are the shifter boots? And there may be a top link boot under the seat. If any are bad, they will funnel water in if stored outside.
When filling the transmission, pouring the oil in the fill hole on top of the transmission must be done very slowly, in increments so the oil has time to distribute back to the intermediate and final drive cases. Pour it in too fast and it will flood the clutch from less than perfect input shaft seals. An alternative is to fill it through the right round cover below the seat.
If yours has a loader, chances are there is an engine driven hydraulic pump with a separate reservoir built into the loader frame. That is a stand alone system that will use RO type medium hydraulic fluid.
You really need to invest in a shop manual, they are not expensive, and will more than pay for itself in mistakes not made and peace of mind decisions. You can get most on this site, or find used ones on Ebay. Get a real hard copy manual that you can carry to the shop, make notes, get it dirty! Those grease stains will have lasting memories down the road!
About the air filter, did you know there is a wire mesh inside the canister that needs servicing? It is rarely mentioned, and is a real bear to get out, but if it's been neglected for 60 years, you can bet it is a solid cake of dirt!
Hope this helps, keep in touch, we're here to help!
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
