Posted by baydog1 on August 16, 2022 at 08:03:45 from (174.206.109.252):
In Reply to: FORD 801 VALVE COVER posted by baydog1 on August 12, 2022 at 13:02:58:
Thank you everyone for the help with the valve cover and everyone was right. It does come off and it wasn't to bad but I did have to hold my mouth just right, say the right words, I bent the tabs up a little bit and defiantly roll it over and out the right side. So thanks again everyone! Reason why I had to remove valve cover is the tractor ran perfect for the job I was doing. It got to dark outside so I figured to finish the job the next morning. Jumped on tractor next morning. When I cranked it over to start, sounded like it had no compression. Long story short it didn't have any compression! One push rod on #1 cylinder had kicked out and fell forward at the top toward rocker arm and didn't bend, push rod on #2 cylinder was out at the bottom and bent. Had to happen when I shut the engine down. So all men, women and children please learn by my mistake!! DO NOT let your engine do that spitting, sputtering and running backward like we've all have done at one time or another with any gas motor. I usually slow engine down to as low as I have the idle set, and I set it low for that creepy crawl but not this time...Had it running a little above idle when I shut the engine down. Did what anyone would do when the dinner bell rang...shut the tractor down and it wanted to spit and sput and run backwards so I did like we've all have done with almost any gas engine and that was, hold down on the brake for like 3 seconds and it shut down...Next morning no compression. Had to happen because I didn't let come all the way down to slowest idle. So everyone...Don't do what I did!! Dinner was good but lunch time sucked the next day :-) Now I got to figure out how to remove push rod.. Gas tank gonna have to move this time I believe. Anyway thanks for all your help and remember to bring your engine down to complete idle when shutting down!
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Hydraulics - The Basics - by Curtis Von Fange. Hydraulics was one of the greatest inventions for helping man compound the work he can do. It’s amazing how a little floor jack can lift tons and tons of weight with just the flick of a handle. What’s even more amazing is that all the principals of hydraulic theory can be wrapped up in such a small package. This same package applies to any hydraulic system from the largest bulldozer to the oldest and smallest tractor. This short series will take a look at the basic layout of a simple hydraul
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
