np, as is typical when anyone asks an electrical question, sooooooooo many responses may cause you confusion, so FYI here again are the very basics:
NOT knowing whats inside that box..... Hot (may be since it operates the light?? or they may have switched the Neutral ??) ,,,,,Neutral (maybe or maybe not??) Ground (maybe or maybe not) NONE of us are there to know for sure and youre inexperienced SO BE CAREFUL
Under the old two wire system (Hot and Neutral) a 2 pin Receptacle will function if it has a Hot and a Neutral with 120 VAC.......A later 3 terminal receptacle will still function even if it has no Ground....
Under the later three wire system (3 pin grounded receptacles) a later modern 3 terminal receptacle requires a Hot, a Neutral, a Ground.
EITHER can switch the Hot so the light goes on and off WELL DUH that can be so regardless if there's a Ground or Neutral available BUT A NEUTRAL IS NEEDED FOR A RECEPTACLE
I (retired power engineer) would NEVER NEVER NEVER advise a DIY non electrician to rely on the conduit and metal box connections AS AN EQUIPMEMNT GROUNDING CONDUCTOR......While in certain applications metallic conduit and metal boxes given proper connection techniques CAN QUALIFY as an Equipment Grounding Conductor there are so many wrong improper conditions that can cause its failure ITS YOUR LIFE YOUR CHOICE
HOWEVER I support anyones right to do as they well please !!!!!! use the conduit as a ground if you like
Its sounding more like due to your inexperience you might hire an electrician !! If you try to DIY based on whats posted here and get it wrong you could cause a fire or a tragedy !!!!!!!!!!!!
Sooooooo do as you please its NOT rocket science and many DIY no problem all I can do is try to educate you and hope you get it right and safe
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.