Posted by DR. EVIL on April 30, 2023 at 12:20:30 from (174.192.64.43):
In Reply to: I.H. H tractor posted by tom levandoski on April 29, 2023 at 07:39:49:
I worked at FARMALL in Rock Island for 4-5 years, in both production assembling front axles and in Purchasing also called Matetial Scheduling. We dealt with all but a few of IH's iron foundries, Louisville was the Big one, Memphis, Indianapolis, IH had a nice newer little ductile iron foundry in Waukesha, WI, and until about 1970 FARMALL itself poured lots and lots of castings. We really didn't buy castings from outside foundries, EXCEPT, the wide front axle castings on 86 & 88 series tractors was ductile iron, too big for Waukesha, had been done at Memphis until about 1979 when we got a semi-truck load of weird greenish colored castings, yep, from John Deere Silvis, Ill foundry about 8-9 miles due east of FARMALL, WE SAVED several hundred Dollars per truckload just on freight. Yes, castings move and relieve stress after machining, only 2-3 thousands of an inch, thermal treatment and vibratory treating of castings before machining is used to normalize the castings. Most stuff on tractors is small enough it doesn't matter. We had a quality team at a food & chemical equipment mfg company that made huge high pressure pump housings, 5 & 7 cylinders arranged like a John Deere A and the cylinders and heads were huge machines forged stainless steel bullets. The machine base moved a little, the head & cylinders didn't. We put a lot of time and expense into the project just to decide it didn't effect our machine. We had our own coordinate measuring machine, we could measure anything to.00001 inch repeatability, if it moved we would know.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.