Posted by Leroy on December 05, 2023 at 07:13:23 from (98.30.20.69):
In Reply to: Re: 8n ford no start posted by Tim PloughNman Daley on December 05, 2023 at 05:29:22:
Tim, what you forgot to mention on those 2 5/16 inch hex bolts is the length, they can only be 7/8 inch long, found out orignals were the 7/8 inch as if you put a 1 inch bolt in it hits the gear on the cam and will cut a slot in it as there is a bit of forward -back play in the cam shaft. 1 1/4 inch long would lock up the engine so it would not turn over. I have a 9N that was having a bit of a knock in it and garage told me it was wrist pins. I knew it was needing an overhaul As it was using oil. Pulled engine out and found the orignal sleves were cracked so new sleves BUT what was making the knock was the bolts holding the distributor on were replaced with one inch long bolts and no washer and they were hitting the ridges on that cam gear and every time the cam turned the bolts would hit that gear and it cut groves in the gear.. It was in 2004 that the tractor was torn down and just this last year engine got put back together but is not yet instaled in tractor due to my health and an ice storm that took all the power lines at farm down and did not have power to shop for a few years before I finaly got them up. By that time I lost the farm and a friend took the tractor and got the engine back together but has not yet got it installed also partialy due to health problems. I am 80 and he is 70, was hoping to get engine installed this past summer but more health problems. The 9N is a 41 model and I have a 1944 2N that Dad bought new in May of 1944 when I was 9 months old. And we do have all the manuals.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
