Posted by Mnethercutt on December 11, 2023 at 08:41:58 from (57.140.108.46):
All,
I've recently acquired 3 new (to me) tractors that have all sat for a considerable amount of time. As part of the repairs I plan on going through the carbs and soaking them, along with the carb for the tractor I've owned for a while. The way I do this is to spray down any stuck parts w/ PB blaster, disassemble the carb, and then I use an ultrasonic cleaner to clean the parts. The concoction I have in the cleaner is a mix of white vinegar (to get after rust), ATF, and acetone. It works GREAT at cleaning the parts. The issue I'm running into is after removing the parts, rinsing them off, drying, and starting reassembly, the parts start to flash rust within a few minutes. While I plan to paint the exterior of the carburetor, my concern is that rust forming on the inside will plug up jets and prevent the needle from seating properly. I can try and coat the inside and passages with oil but its difficult to ensure that it gets everywhere and I'm unsure how long it will realistically last. So far the flash rusting has happened on two carbs I've attempted to clean in this manner.
So, what can I do to stop the flash rust or what am I doing incorrectly to cause it? I've seen where you can "season" cast iron pans and such but I'm not sure if that's advisable, let alone possible with a carburetor.
Anybody have any experience or wisdom in this area?
Thanks!
Also, if it matters, the tractors are a 1948 JD A, 1949 JD B, 1950 Farmall H, and a 1962 JD 1010. Might be a year or two off on some but that's ball park.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Harvestin Hay: The Early Years (Part 2) - by Pat Browning. The summer of 1950 was the start of a new era in farming for our family. I was thirteen, and Kathy (my oldest sister) was seven. At this age, I believed tractor farming was the only way, hot stuff -- and given a chance I probably would have used the tractor, Dad's first, a 1936 Model "A" John Deere, to go bring in the cows! And I think Dad was ready for some automation too. And so it was that we acquired a good, used J. I. Case, wire tie hay baler. In addition to a person to drive th
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
