Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Placement of Ballast Resistor


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Gene-AL on January 16, 2006 at 14:47:48 from (65.4.38.60):

In Reply to: Placement of Ballast Resistor posted by Thomas Donahy on January 15, 2006 at 07:27:04:

Thomas,
My take on your original question: The return path from the sparkplug ground for the high voltage current has two low-impedance paths: One through the battery, switch, and ballast to the coil; the other through the condenser to the coil. The high-voltage arc current is very small (a few milliamps) compared to the primary current, and would have little, if any, effect on these two low voltage paths. Placement of the ballast resistor before or after the coil would seem not to matter, except for 12V switched starting.

It might be useful to consider the current in the two joined circuits which form the Kettering ignition system. The primary coil winding could have currents approaching 8-10 Amps with the points closed which will, through inductive field collapse in the coil primary, maintain that same current through the points at the instant they start to break open. Without a condenser in place, some of the stored energy will dissipate in a hot arc across the points, saping total field energy available for the high voltage ciruit which triggers at the same time. The arc will also erode the point contacts excesively.
However, with the capacitor properly in place and initially at zero volts charge (the points had it shorted prior to this time), the high initial primary current can continue at point opening as the coil's field collapses and the condenser charges. The current then falls at a rate set by the capacity of the condenser. At point opening, all the coil voltages reverse in polarity and spike, then will oscillate (ring) back & forth (AC), falling to zero in a fraction of a second.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Usin Your Implements: Bucket Loader - by Curtis Von Fange. Introduction: Dad was raised during the depression years of the thirties. As a kid he worked part time on a farm in Kansas doing many of the manual chores. Some of the more successful farmers of that day had a new time saving device called a tractor. It increased the farm productivity and, in general, made life easier because more work could be done with this 'mechanical beast'. My dad dreamed that some day he would have his own tractor with every implement he could get. When he rea ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy