Tractor Talk Discussion Board |
Re: T400 easy swap
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by jdemaris on November 01, 2006 at 05:54:47 from (69.67.229.173):
In Reply to: OT: 1986 Chevy Truck transmission swap posted by Brad in WI on November 01, 2006 at 02:34:57:
T400 is a pretty easy swap and is the most rugged auto. trans. GM had at the time. I have two 83 diesel Blazers that I converted year's ago - from the 700R4 to the T400s (3.08 axles). I have a mechanical governor in one (no modulator), the other's all use a vacuum simulator valve (VRV) to mimic throttle/vacuum reponse like a gas engine has. So, changeover in a gas engine truck is easier than my swaps. You can buy adapters to go between the transfer case and trans - but finding a donor vehicle is easier. I have one if you need it - but I'm in New York. I've got a low-miles 4WD 89 Suburban with an excellent T400 trans, torque converter and 241C transfercase. I recently let my son take the engine from it, and I'm going to take half the frame for a K5 Blazer motorhome project. My 86 diesel Blazer was recently changed over -same deal (3.08 axles) In the case of my 87 3/4 ton 4WD Chevy Suburban and 89 GMC Suburban (both diesels) - the dealer would not sell them with the 700R4 - since they were both bought as tow vehicles -they both came with T400s and 3.73 axles. The lack of overdrive should not be an issue - unless you've got axles over 3.73. My 87 Suburban made it to the 500,000 mile mark with orignal engine and T-400 trans - with a lot of towing and 75 MPH highway speeds. The 14 bolt SF rear-axle went twice - but that's a different story. Also, since all of mine are diesels - the RPM range is more limited than your gas engine. A 6.2 diesel has an optimal high RPM range of 1800 - 2200 RPM. Your 350 gasser will handle the higher RPMs better - so if I had no problems - you shouldn't either.
Replies:
Home
| Forums
Today's Featured Article -
The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
18-32 Case Cross Motor
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|