Simple, take a M, put it on a dyno, add a digital tach or whatever you got,,, set the dyno at 540, then read the rpm. Do the same for the 400-450. Bout 150-200 rpm difference in the engine speed, no matter how it was tuned, the engine speeds were not the same acording to a tach.
Last year, we built a 175 for a 350,,,, I put the engine in a SH chassis, dyno, and it was 47 hp. Took the same engine, dropped it into the 350. The 350 had no live hyd, (removed) dyno hp was 40 hp out of the exact same engine. Rpm was also different, cause the SH ran slower rpm wise then the 350. Its not much of a ratio difference,,, and only an engine tach, and a pto tach will tell what the actual differences would be,, but, there is a difference.
Another exapmle of the ratio chages was the 350 utility rated at over 2200 rpm!! Yet, at 2200+ rpm or whatever they are set at,, the pto is slowed down to make the engine speed faster to run a higher rpm, and still not overspeed the pto. if they left the ratio the same speed as the H and ran the engine at 2200, the pto speed will be over 700 pto rpm. quite a difference in pto rpm speed IF they never chaged anything at all.
Pullers, well they like to brag on how much power an engine makes by itself,,,, and those readings they take are not rated rpm for a tractor. More like high performance race cars,,, where the spin em til they find what they are looking for. Most cases, 500 engine rpm or more over rated rpm to get the big numbers. Our shop, has always pto dyno tuned engines,,, so no matter what,, the power it puts out is rated rpm for that chassis, and its speced out for 540 pto speed for that model. I keep the tractor in the pulling, cause not all pulling tractors, only see track duty, most do both, work and play and they use the pto!
Find a pto tach, an engine tach, and the models mentioned above and do some tests. I did, but you can lead a horse to water, but dont mean, the horse will take a drink. But, we try like heck. Have a good day. ChadS
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Harvestin Hay: The Early Years (Part 2) - by Pat Browning. The summer of 1950 was the start of a new era in farming for our family. I was thirteen, and Kathy (my oldest sister) was seven. At this age, I believed tractor farming was the only way, hot stuff -- and given a chance I probably would have used the tractor, Dad's first, a 1936 Model "A" John Deere, to go bring in the cows! And I think Dad was ready for some automation too. And so it was that we acquired a good, used J. I. Case, wire tie hay baler. In addition to a person to drive th
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
