Tractor Talk Discussion Board |
Re: WD andWD45
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Brian G. NY on March 16, 2001 at 09:23:54 from (216.238.173.239):
In Reply to: WD andWD45 posted by Shank on March 15, 2001 at 19:54:15:
WD HP: 34.63 belt/30.23 drawbar - WD-45 HP: 43.21 belt/37.84 drawbar. There were running changes made to the WD from 1948 til mid 1953 when the WD-45 replaced it. So.....the fact that it may have the curved shifter(helical gear tranny), the "tall" heads or a distributer will not necessarily indicate the tractor is a WD-45 as these were running changes made to the WD. If the tractor has a serial # of WD144607 or higher it should be a WD-45. Likewise, if the engine serial # begins with 45 rather than WD it should be a WD-45. The most obvious visual difference between a WD & a WD-45 engine is the plate bolted on to the LH side of the WD engine vs. a solid cast block on the WD-45. When looking at a WD-45, you will see that the carb is larger as is the air inlet tube, but these are not too obvious unless you have the two tractors sitting side by side. The stock rear wheel widths are 11" on a WD vs. 13" on a WD-45 and the fenders are a little higher. Many running changes were made to the WD-45 over the years. The snap-coupler was standard equipment on the WD-45 beginning with with Ser. #WD151381 but was optional long before that on the WD and many early WDs were retrofitted with it, as well. The number of plates in the transmission (hand) clutch were increased from 2 to 3 with WD-45s beginning with Ser. #165056 and the WFE front support plate was changed from 3 bolts to 4 with WD-45 Ser. # WD186413. Power Steering was introduced as an option in 1956, but there again, many earlier WDs & WD-45s were retrofitted with it. I'm sure I left out some differences, for example, the radiator shutters were eliminated at some point, but I don't know when.
Follow Ups:
Home
| Forums
Today's Featured Article -
Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
Latest Ad:
18-32 Case Cross Motor
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|