Okay since Im NOT THERE and have to make several guesses and am unsure what you mean by " It only has one 2+ground wire coming into the box" NO WARRANTY ON MY ANSWERS
IF?????? The "box" has two insulated wires (bigger gauge like 8 or 6 etc) and one bare/green wire my best GUESS is it used to supply 240 volts to a stove (Depends on wire size also??) Iffffffff thats the case it used to be wired to a 2 pole 240 volt breaker NOT a single pole and the voltage would read 240 line to line or 120 from either line to the bare/green ground.
Old 240 volt stoves used 3 wire feeds, 2 hots and 1 bare/green equipment ground. ITS NOT CORRECT TO USE THE EQUIPMENT GROUND AS A NEUTRAL RETURN (i.e. 120 volts line to ground) although that took place in some old stoves
NOWWWWWWWWW if those 3? wires are now instead connected, 1 to a 120 volt single pole breaker (or only one side of a 2 pole breaker) and 1 was NOT connected, and 1 is to the equipment ground buss....................You would measure 120 volts across the wire to the breaker and the other bare/green equipment ground..........0 volts across the unconnected wire to any of the others
Just trace out the wires and see where they are connected in the electrical panel.....If ones to a single pole breaker (or only one side of a 2 pole breaker) and the other to the equipment ground buss, you measure 120 volts across those 2 butttttttttttttt the bare/green equipment wire IS NOT SUPPOSED TO BE USED AS THE NEUTRAL.
If you wanna use those wires to feed 120 volts, Id wire the black to a single pole breaker, usually white to the Neutral Buss,,,,bare/green to the equipment ground buss. In some panels theres only one buss where Neutrals and Grounds BOTH wire.
If you wanna use those 3 wires to feed a 240 volt circuit, wire one insulated wire to one side of a 2 pole breaker, the other insulated wire to the other pole on a 2 pole breaker, the bare/green to the equipment ground buss
NOTE a metallic junction or outlet box also needs bonded to the equipenmt ground ya know.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Uncle Cecil's Super A Lives Again - by Mike Purcell. A week or so out of most of my childhood summers was often spent with my Uncle Cecil and Aunt Sissie in the small East Texas town of Maydelle on their 80 acre farm. Some of my fondest memories of these visits are those of learning to drive a tractor at the helm of Uncle Cecil’s 1948 Farmall Super A. Uncle Cecil was the second owner of this wonderful little tractor, but it was almost as though he had adopted an infant. The original owner was a man from Minnesota who bought her from a local dea
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
