Tractor Talk Discussion Board |
Re: Placement of Ballast Resistor
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by KEB on January 15, 2006 at 08:45:16 from (192.91.171.36):
In Reply to: Re: Placement of Ballast Resistor posted by Allan in NE on January 15, 2006 at 08:05:39:
Quick explanation - I"m unfortunately at work this morning & can"t spend much time. First, the high voltage pulse is not DC. The inductance of the coil and the capacitance of the condenser form a resonant circuit which "rings" when it is stimulated by the rapid collapse of the magnetic field in the coil when the points open. A mechanical analog of this is a guitar string which "rings" when it is stimulated by a pick. The wave form is actually a damped sinusoid, modified a little by the non-linear characteristics of the spark gap. The impedance through a capacitor (condensor) is a function of the rate of change of the applied voltage. A fast transient such as the high voltage output of the coil has a very fast rise and fall time and does in fact pass right through the condensor (with some phase shift, which is immaterial to this discussion). If the pulse did not pass through the condensor, it would arc across the points and destroy them in short order. In fact, one indication of a failing condnesor is metal transfer from one point contact to the other as a result of the arc. If you ever encounter a set of points with a pit on one side and a corresponding mound on the other, the first place to look is the condensor. Allan, the primary and secondary windings are in fact connected. Check a coil with an ohmmeter. The coil is a autotransformer, with the primary and secondary windings connected in series. There are only three connections, the "+" terminal which is the common connection between primary and secondary windings, the "-" terminal which is the "bottom" of the series windings, and the high voltage terminal which is the "top" of the series windings. Hopefully, I"ll be out of here in a few hours today. If I get a chance in the next couple days, I"ll post a schematic (or a link to one) showing the current paths.
Replies:
Home
| Forums
Today's Featured Article -
Usin Your Implements: Bucket Loader - by Curtis Von Fange. Introduction: Dad was raised during the depression years of the thirties. As a kid he worked part time on a farm in Kansas doing many of the manual chores. Some of the more successful farmers of that day had a new time saving device called a tractor. It increased the farm productivity and, in general, made life easier because more work could be done with this 'mechanical beast'. My dad dreamed that some day he would have his own tractor with every implement he could get. When he rea
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|